You don’t have to be a professional to cut through the wood in your kitchen.
It’s a quick and easy method that can be done at home with just a few tools.
But if you want to get serious about making a DIY cut, you’re going to need to invest in a professional kitchen toolkit.
Here’s how to get the most out of your kitchen and get the best results.
How to cut your own kitchen cut What you need to know to get startedWhat you need: Cutting tools and a rulerWhat you will need: A cutting mat (or a table saw if you’re using a table)Steps: Cut your first piece of wood into 3cm lengths.
Then, cut into a 3cm length using a piece of cut wood.
Cut out the wood to make a hole.
Then carefully cut a second piece of the same length.
Steps on a table: Cut a piece that’s about 4cm in length.
Cut a hole in the centre.
This will hold the pieces together and allow you to trim away at the wood and create a neat cut.
Step on a cutting mat: If you’re not using a cutting tool, cut your piece of mat in half.
Then cut into three equal pieces and then fold in half, each piece into a triangle shape.
Then put a ruler in the middle of each triangle.
Step with a ruler: Cut two equal pieces of the table saw.
The first piece should be about 4.5cm long and the second piece should measure about 5cm long.
Cut through each piece of table saw and into the wood.
Step two: Cut out a triangle and place it on the table.
Use the table knife to cut the top of the triangle out of the wood using a knife blade.
Then remove the knife blade and place the blade on the top.
This should give you two pieces of wood that are about 4 cm apart.
Step three: Repeat steps two to three for the other three pieces of table.
Step four: Using the knife, cut the first two pieces out of each piece.
You should now have three pieces that are 4 cm and 5 cm apart, which will allow you enough room for trimming and shaping.
Step five: Now you should have three separate pieces of lumber that are 6 cm and 7 cm apart that you can trim with the knife.
Step six: Cut the second triangle and use the table cutting mat to make two smaller triangles.
Use a ruler to cut these out of both the wood pieces and the table wood.
Repeat the process for the third piece of triangle.
The three pieces should be 4.25cm long each.
Step seven: Using a small bit of table lumber, cut out the bottom of the bottom half of the second cut out triangle.
Use your table saw to cut out a square of this piece of timber.
Cut it into two equal sections, then trim the two pieces to create a square.
Then trim the remaining wood to create the triangle.
Cut a square out of two pieces from the bottom two pieces.
Use an awl to secure the piece to the wood frame.
Step eight: With the saw, cut a square to form the triangle using the saw to trim the wood piece in half (you’ll cut it out with the saw).
The two halves of the saw should now be 5.5 cm long.
Step nine: Use the saw again to trim off any excess wood you may have left over.
The final piece of wooden will measure about 6.5 to 7 cm in length and about 5.75 to 6.25 cm wide.
Step ten: Using your table, make another triangle from the same piece of lumber.
This time, cut it in half lengthwise.
Place the piece of saw on the bottom with the blade pointing up.
You’ll see a cut line on the wood, this is where you’ll trim the edges of the triangles.
Step eleven: Now use your table to cut another triangle, this time 5 cm long and 6 cm wide from the second one you cut.
Cut the remaining pieces to lengthwise, then use your knife to trim these pieces into the three pieces you just made.
Step twelve: Take the pieces you’ve cut and put them together with a square and the triangle on top.
Make sure that the pieces are straight, then place the square over the cut out of a piece.
Make a small mark on the square using a ruler.
Step thirteen: Cut each triangle and trim the top one to the size you want it.
Now, trim the bottom piece and make another mark with a piece saw.
Now you have a nice, neat cut and it looks like you’ve finished your first kitchen cut!
You can also make a couple of other kitchen cuts from this tutorial, including using a saw to shape wood into a piece and a cutting with a router.
If you want, you can use these to cut some other decorative pieces.